Wifi repeater 192.168.10.1 setup wizard
With the help of these WiFi Extenders, one can improve the intensity of WiFi connection and coverage with no stagnant points. The actual work these units do is improve the signal strength and pick it up from the router and spread it all over to the nearby place. These extenders help in clearing dead spots and give full coverage across your home. There are various options of these extenders like when you want high-speed connection there is an extender named Madpower AC1200 Extender. In case you want an extender just for streaming and another general-purpose then you can go for Madpower N300 Wireless-N extender. The web address myrepeater.net is basically the local address that is used for configuring the setup of the wireless repeaters like all other devices available in the market. Also one can easily login to the repeater using this web address myrepeater.net. If you need any expert assistance or whenever you face any issue regarding the configuration and setup of myrepeater.net address, our team of experts is available 24×7 to assist you in resolving your issues regarding repeater.setup.
Setting up of reapeater by using the web address myrepeater.net
- Firstly, the range extender or repeater is to be placed near your wireless router.
- Then, plug in the range extender to the power outlet and must be placed between the Linksys router and the area having no Wi-Fi signal or dead zone.
- To setup the connection with router, one has to just press the WPS button on the router and thereby pressing the WPS button on the repeater as well.
- Within few seconds, the connection to extend the signal will be established.
- To setup the repeater, one can also use the Ethernet cable to connect the router with the repeater.
- Then, one can use any browser to open the web page myrepeater.net
- If the page on the particular browser does not get connected, you can use the IP address 192.168.10.1 to setup the connection.
- Once the setup page gets connected, one may choose the mode as wireless range extender option or access point option or wireless repeater mode to configure the extender according to the requirement.
- Now, choose the network you want to extend and click Next button.
- Finally, submit the requirement by clicking on finish button.
- After submitting, the connection will be established between the router and wireless repeater.
- Now, you can place the repeater anywhere in your home.
Setting up of Wi-Fi repeater by using WPS Method
- Firstly, plug in the wireless repeater to the power outlet and must be placed between the router and the area having no Wi-Fi signal or dead zone.
- Then, simultaneously push the WPS buttons provided on both the devices- router as well as repeater. Press the WPS buttons until the LED turns ON.
- You can check the status of the WPS connection just by monitoring the WPS LED.
- Once the LED turns ON, place the wireless repeater in between the wireless router and wireless device to attain maximum signal strength.
- Once the LED light turns solid green, this means that the repeater has successfully connected with the Wi-Fi repeater.
- If in case, only one Wi-Fi LED turns ON, then you need to repeat the process.
- Again press the WPS buttons on both repeater and router.
- Now, open the browser of your choice.
- Search for the web address myrepeater.net or IP address 192.168.10.1.
- Then you can login using the default credentials i.e. username (admin) and password (admin) to connect to the extended network.
- Now, successfully complete the wireless repeater setup by simply following the instructions given on the setup page.
Setting up of wireless repeater manually by using Ethernet Cable
If your WiFi extender has LAN ports and its actually in a position where you can hardwire Ethernet cable connection. You should always go for it. By routing some of the wireless connections into hardwire, you free up some of the air time and generally improve the speed of your entire network. To setup the repeater using the Ethernet cable, one must follow the below given steps:
- One can use a Desktop or Laptop to connect the Ethernet cable with wireless repeater.
- Then, one can use any browser to open the web page myrepeater.net
- Then, by using the default username (admin) and password (admin), one can login into the setup page.
- Once the setup page gets connected, one may choose the mode as wireless range extender option or access point option or wireless repeater mode to configure the extender according to the requirement.
- Now, choose the network you want to extend by filling the SSID (network name) with wireless password that you want to setup for your repeater and click Next button.
- Finally, submit the requirement by clicking on finish button.
- Now it’s time to reconnect all the wireless devices to the repeater.
