Wavlink AC1200 WL-WN579X3 double band extender accompanies astonishing Wi-Fi range and Wi-Fi solidness. It accompanies incredible offices like driving 802.11ac Wi-Fi standard, high force enhancer and shaft shaping innovation. It accompanies 2.4GHz and 5GHz double band, so it comes future-prepared. On the AC1200 extender, there is GFI outlet, LAN port, Status LED, WPS catch and warmth scattering zone. It arrives in a minimal body and four high increase radio wires. Wavlink Aerial X extender will dispense with all your Wi-Fi dead zones.
Let’s start the Wavlink Aerial X AC1200 WL-WN579X3 extender setup via WPA:
- First unbox wavlink aerial x extender, connect Wavlink WN579X3 repeater near to the router.
- Now check the router properly as it is functioning and also comes with WPS technology.
- Then reposition the antennas in such a wayfor maximum coverage.
- After that find WPS button inWavlinkextender andon router.
- Now push the “ON” button on the extender.
- Make sure to reposition the “Access Point/Repeater/Router” button to the Repeater.
- Press the WPS button for 10 seconds in Wavlink aerial X AC1200. Within 2 minutes press & hold the WPS button on router also.
Note:Read the router’s manual to know more about the WPS button on the router.
- Confirm whether extender lights LEDturns to blue which signifies the connectionis successfully done.
- Now you can place the extender where to want to extend or in dead zones in your home.
- Enjoy your enhancedWi-Fi experience with a WL-WN579X3 repeater.
Wavlink Aerial X AC1200 WL-WN579X3
Wavlink Aerial X AC1200 WL-WN579X3 setup as Repeater via WEB-UI
Extender setup is often through with online browser like Google chrome and Mozilla Firefox which are suggested for an extended router connection. You can visit Wi-Fi.wavlink.co for connection.
- Firstly confirm your Wavlink Aerial Repeater and routerboth are in working conditions.
- Now connect the extender to an electrical wallnear to your existing router.
- Then reposition the antennas vertically to the ground for good coverage.
- Make sure to switch “ON/OFF” to “ON” on the extender.
- Now hold on for moments until power LED turns to solid green.Switch the mode button to “Repeater” on the Wavlink WN579X3 repeater.
- Then acquireyour any device like phone or laptop and connect extender to router via Wi-Fi Wavlink.com.
- Make sure to connect your device withWi-Fi signal having name SSID as “wireless N” or “wireless AC”. For first time it won’t ask you for any password.
- Once you done the whole process then launch web browser from the same device and type in the address bar either IP address 192.168.10.1 or Wi-Fi.wavlink.comfor Aerial X AC1200 WL-WN 579X3 setup.
- After that you will see the login page, here enter credentials password as “admin” and click login.
- Now click the “wizard” option on webpage and click “repeater”. Choose the name of router want to connect and enter the correct password for the same.
- Once you done then hold on for moments as it takes for the setup to finish.
Now use any device and connect to the extended SSID of the Wavlink Extender and apply the same password as a router.
Wavlink Aerial X AC1200 WL-Wn579X3 setup as Access Point
Wavlink extender is often used as a repeater and as Access point. You’ll connect your quality Ethernet cable to LAN port in Wavlink extender to make a Wi-Fi hotspot. You’ll setup an AC1200 WL-WN579X3 as Access Point from any android/ios device or any Desktop/Laptop.
- Firstly makes sure to connect the Aerial X AC1200 repeater into an electrical wall.
- Then reposition the external antennas forgood coverage.
- Now switch ON the extender with OFF/ON button of the WN579X3 repeater.
- Make sure to switch the mode button to “Access Point” on the Aerial X.
- Place the LAN port on it and put the wired Ethernet cable and connect the Wavlink extender Wi-Fi from any of your device and select the SSID name. If you are doing first time then no password is required.
- Now from your device launch web browser and type in the address bar 192.168.10.1 or Wi-Fi.wavkink.com.
- Now you will see the login page here, type the credentials password as “amin” (Default password).Once you done the click “wizard” from the page and select “Access Point”.
- Hold on for few minutes and once the percentage bar reaches a hundred, you’re ready to go.
- Now you can place where you find dead-zone at home.
Wl-Wn579X3 repeater Firmware update
Wavlink extender will do the updates timely for better performance and to repair bugs. Extender’s software is important as hardware then we’ve mentioned the steps to update your WL-WN579X3 repeater Firmware.
We can establish the way to update Firmware of your Wavlink Aerial AC1200 extenderbyfollowingthese steps:
To confirm whether there’s an update for your Wavlink extender, you need to fasten any of your device.
- Firstly launch any of web browserson device and type in the address bar 192.168.10.1 or Wi-Fi.walink.com.
- Now go to the setting menu and click on update.
- Then place and click the check online button.
Note:If you find any update there then follow the prompts and download into your device.
- Once you done extracting downloaded file, then click the browse button and place the extracted files.
- Remember to upload the file from device.
- The firmware update will before long beginning and your Wavlink Extender will be refreshed soon.
Firmware updates make your Wavlink Extender all the more quick, steady and solid. The firmware update enhances your extender at a minor or large level. No appropriate update can make the system less effective and less secure.
How to reset Aerial X AC1200 WL-WN579X3?
Wavlink extender is anything but difficult to utilize and superfast, however once in a while you have to reset the system because of different reasons like exchanging your extender, issue with the firmware. Follow the means to comprehend the Aerial X reset process. The factory reset will reset every one of your settings and all the information.
- First grab anything(clip/pencil).
- Then find the factory reset hole on the Wavlink Aerial X extender.
- After that push the factory reset button for seven seconds.
- Once you done pressing it for seven seconds, then release the button.
- Automatically extender will soon restart with factory default settings.
Note:Hold on for few minutestoproperly reboot the extender.
- Also, you can reset extender via web browser as well. You can follow these steps.
- Firstly enter the extender management page.
- Then click “Reset” from the “Backup/Restore” on setup page.
- Hold on for few seconds.
- After a few seconds, the repeater will automatically reset to factory default settings.
